AnyVape Davide BDC Glassomizer - Aspire Version
Aspire Bottom coils coils will fit and work with this tank! This can also be converted into the Standard Davide ( the protank coil version) if you remove the thicker base piece.
(see Eric's review notes below for extra information)
Tube Locking Systerm
All Parts Changeable (especially glass tube & drip tip)
3.0ml Capacity (when filled vertically, slightly less filled at an angle)
Bottom Coils for better wicking
Cleans easily with the removable parts
Compatable with eGo Series Batteries,Mods.
1 Davide BDC Glassomizer
1 eGo battery cone
2 Davide BDC Coil Heads, one is preinstalled one in the packing. (I recommend the aspire coils as we do not carry the anyvape coils)
This is the BDC version that takes Aspire coils NOT Protank coils. (but see below for more info)
Clean all parts before using, the glass, the base and the top! Please be careful with this tank, it is made of glass and can shatter and break if dropped. Breakage of the tank is not warrantied. Filling this unit is different from the protank as this unit has guards on the base, so you would fill with a dripper, syringe or bottle carefully into the sloted holes and not just dump in it.
When building this tank or removing parts, please be sure to clean and dry all parts. When rebuilding the center tube make sure the center tube is on properly and tight, not having it all put together properly will result in leaking. Do not overtighten the top or bottom base, finger tight is good. I grasp the top and bottom with both hands (one on top the other on the base) and twist slowly until it stops, it does not need to be tightened more than that, over tightening can cause breakage. Glass Breakage is not covered under any warranty. Coil head ohms may vary, your preferred ohms are not warrantied
The glass tanks that are coming out of China recently require a little finese in usage, do not store in pockets, try not to drop them and be careful putting them back together.
This unit is the Davide BCC with an extra part to make it the "BDC" it has a second upper base
This is basically like a protank that can be dissasembled, but it does not take Protank coils, only the new awesome aspire coils. it is contructed well, the glass is nice and it all comes apart even the center stem, Not sure on the ohms included as they seem to be random.
Ok, so remember how I just said it can't take Protank coils? Well it can, but you need to adjust it. If you take out the upper base (the piece with the rings around it) you can then use Protank coils on it. That is the only difference between a Davide BCC and a Davide BDC. Be careful not to lose either piece or you will not be able to use the aspire coils on it. As a bonus, this piece can be swapped onto a Protank II and then the Protank II can then use aspire bottom coils! (this is not warrantied or guaranteed)
One issue I have found is that the drip tip comes out too easily, just like the standard Davide before it although slightly better, it doesn't fall out but it doesn't takes much pressure to remove it, it is not tight enough, but it is an improvement over the previous Davide, so they are moving in the right direction here.
Showing reviews 1-20 of 31 | Next
Posted by Dean Esmay on 2nd Aug 2014
These are awesome tanks. I was loyal to Kanger Protanks but I bought one of these just for the heck of it and I'm IN LOVE with it. It's every bit as good if not better than the Protank 2 or 3. It looks great, AND it holds more liquid.
If you buy one of these as a replacement for a Protank II or III you will NOT be sorry, they're a better product for a cheaper price--although I do strongly recommend you also buy a Kanger Airflow Control Valve, which works like a champ and really improves the experience.
I wish I'd just started right off with the Davide. This. Thing. Is. AWESOME
Posted by notalion on 19th Apr 2014
As good as or better than the protank, works great with the aspire bdc or the kanger coils.
Posted by Brian on 27th Feb 2014
Was skeptical about the aspire heads, never a fan of dual coil anything, but this thing is awesome, no leaks, no gurgles, no dry hits at 50/50. ..retired my protanks, and ordered more of these.
Posted by James G. - Auburn, GA on 27th Feb 2014
Three weeks on and I still haven't had one problem with this unit. 2.1Ω replacement coils work better than the 1.8Ω that came with it, so I would suggest buying those too.
Posted by Sonya on 26th Feb 2014
No problems with leaking, juice tastes great, and easy to disassemble and clean. By far the best glassomizer I've tried.
Posted by Jared bradley on 24th Feb 2014
This is a great tank. Some complain about the BDC coil having problems after refilling tanks that use them. I think I figured it out, it's simple you have to leave some air in the tank. When you fill it to the very top your creating a vacuum suction in the tanks. I will be buying more of the Davide Anyvape Glassomizer. LOVE IT.
Posted by SimonSaysVape on 24th Feb 2014
This is my first dual coil, and I am really liking it. I have been vaping on this tank for about a week now, with zero problems.
Posted by Cah on 20th Feb 2014
I purchased one because I loved the aspire products. This is the is hands down been the best tank I have used for the aspire line of heads. For the price I just don't think this thing can be beat.
Posted by Vicegrips on 18th Feb 2014
Three reasons I tried this tank:
Glass - avoids problems with plastic tanks and some juices
Fits in my VTR - no extension piece needed.
Aspire coils - I already have a couple Aspire bdc tanks and extra coils.
So far I'm very happy with the Davide's performance. I vape mainly DIY juice, 12% 70/30.
Posted by Jim on 31st Jan 2014
The design is basically a Protank with an Aspire adapter. I am a fan of both coils so this is a big selling point for me. The only bad thing I can say about it is the drip tip on mine was way too loose. A friend also picked one up and theirs fit fine, so it seems to be luck of the draw.
Posted by John on 31st Jan 2014
I am going to rank this higher than my protank 2, and I like my protank 2. This glassomiser just performs so good and gives such good flavor.You can do a total breakdown for easy cleaning. I also like that with a few slight changes it can take protank/evod heads. I would rather use the Aspire heads in it though.
Posted by K_Tech on 29th Jan 2014
I bought this tank because I liked the performance of my Aspire tanks, but wanted something with a glass tank.
This fits the bill nicely!
I only gave four stars because it can gurgle a little with some liquids, but not to the point of being unusable.
Posted by carhauler1969 on 25th Jan 2014
When working properly I enjoy this tank better than my Kangers. Like some of the other reviews I've had some issues with the Davide, mainly wicking problems after refilling the tank. It worked beautifully all day yesterday, but after refilling it this morning about every other hit is a dry fire very harsh & nasty tasting. Even after letting it sit for an hour or so in a vertical position the inconsistent wicking continued.
Posted by Jason Feil on 24th Jan 2014
First off, this was my first time ordering from Discount Vapers. I was a little hesitant at first, since this is a much smaller operation than other big name online retailers. Let me say, don't flinch one little bit, order from them now! Not only did my order get to me in good time, but DV offers FANTASTIC prices. Now, the Davide BDC... this tank is a BEAST! I've owner many tanks/cartos/rebuildables in my vaping days, and this thing truly delivers a QUALITY vape. The taste is clean and bold and the vapor production is great. It obviously won't match the performance of an RBA set up correctly, but it seriously comes as close as a "plug and play" unit ever could. Oh, and if you're vaping a thick juice, don't worry at all about how it feeds. I've been vaping a 100% VG juice from it to put it through its paces and I have not experienced a single dry hit or burn, and I'm pushing it all the way to 10 watts! Stop thinking, stop worrying, order the Davide BDC from Discount Vapers with confidence!
Posted by Steve P. on 16th Jan 2014
A big, thick tank that disassembles quickly and reassembles just as easily? Check. Adapted to use a superior atomizer, but can change back to Kanger? Check. Price point? Double check.
Good, clean vape - sturdy (but not invincible) tank - extra o-rings in the box, this tank is absolutely fantastic. Love the adaptability. Love the tank size. I did get a tank leak when I didn't take my time putting it back together, but I can hardly blame the tank for that one.
Only improvement I could see would be tossing in a spare white adapter piece or two. That's about it, though. I love this tank.
Posted by Danny on 10th Jan 2014
Am an original Davide Glassomizer owner and decided to give this BDC model a shot. Now I do enjoy both but this one does give you more flavor and vapor. On the downside it eats up your battery a bit faster due to the dual coil head. Would recommend!
Posted by Tim on 10th Jan 2014
Great tank, the volume it holds is fantastic, and the Aspire attachment makes this thing priceless. Also a great price on these from DV, will definitely be shopping here again. Works better than the aspire bdc from my experience.
Posted by Chani1074 on 6th Jan 2014
Love the dual coil vaping, and I like the AnyVape Davide better than a protank2 in any form, BCC and BDC.....great product!
Posted by Rob P. on 27th Dec 2013
I bought the Aspire version of the Davide, just because I wanted a better looking version of the Vivi Nova style of the Aspire BDC. It is a beatiful device. It does however, have more gurgling issues than the Vivi Nova style tank. Works fine otherwise, and you can't go wrong with the Apire BDC coils.
Posted by scottydoesntknow on 23rd Dec 2013
I already had one of these and I love it, so I decided to get one for my girlfriend. I wanted to clean it first so I disasembled all the parts. I struggled to get the little white rubber grommet out but once I did I realised why, the metal tube that runs up the center of the tank had some kind of defect. The rubber grommet is supposed to be able to fit into that metal tube easily but this one was too tight. I used a small file to file out the inner edge and eventually managed to get it to slide in easily. I was then able to assemble all of the parts again, but unfortunately I chewed up one of the o-rings in the process. Still functonal though.
Showing reviews 1-20 of 31 | Next